Carvin LB70 Owner's Manual

Carvin Musical Instruments Owner's Manual - LB70.
Download
Page  of 1
4.9, 2076 votes
background image

  Congratulations on your Carvin bass purchase.  

With  proper  care  Carvin  basses  will  last  a 

lifetime. 

IMPORTANT

  Within several days of receiving your bass, it 

may  require  a  truss  rod  adjustment,  especial y 

if  your  local  weather  is  either  very  dry  or  very 

humid.  If it is very dry, chances are your neck 

wil  start to acquire too much forward bow.  If it 

is raining or very humid, the neck may become 

backbowed, causing string buzzing.  Please refer 

to the 2-way truss rod adjustment instructions.

STRINGS

  Your Carvin bass is equipped with a high quality 

set of Carvin strings.  For replacement strings, 

please  order  from  our  catalog.    If  you  change 

to  considerably  lighter  or  heavier  strings,  you 

may need to adjust the truss rod in the neck to 

maintain  good  string  action.    For  long  string 

life, keep the strings clean with a soft dry cloth.  

Replace  strings  regularly  to  avoid  dead  strings 

which can cause intonation problems.

2-WAY TRUSS ROD ADJUSTMENT 

    Carvin  basses  come  with  a  2-way  adjustable 

truss  rod,  allowing  you  to  add  the  proper 

amount of forward bow to necks with a reverse 

bow condition.  You can check the neck yourself 

for the proper amount of forward bow.  You will 

need a straightedge about 24” long and a feeler 

gauge  set.    Tune  the  bass  to  the  proper  pitch 

and  place  the  straightedge  edgewise  on  the 

center  of  the  fingerboard  so  that  it  is  resting 

on  the  first  and  last  fret.  Now  take  the  feeler 

gauge set and check for clearance at the 7th fret. 

Viewing from the tip of the headstock (with the 

frets  facing  away  from  you),  the  truss  rod  nut 

must be turned left (counter clockwise) if there is 

less than .010” clearance at the 7th fret. If more 

than .020” clearance, the truss rod nut must be 

turned clockwise.  The optimum forward bow is 

.015”.    Turning  the  nut  to  the  right  (clockwise) 

will reduce the amount of forward bow.  To make 

adjustments use the 4mm hex wrench provided 

with  your  bass.  A  5/32”  hex  wrench  wil   also 

work.  Turn  the  nut  1/10  of  a  turn  and  recheck. 
Do Not force or over tighten the truss rod nut!
  

Note: If you have just received your Carvin 

bass  and  the  string  action  is  very  low  with 

buzzing frets, then chances are the neck needs 

adjusting  because  of  a  backbowed  condition 

sometimes  caused  during  shipping.    If  this  is 

the case then remove the truss rod cover with 

a small phillips screwdriver.  Turn the truss rod 

counter clockwise until you have .015” forward 

bow.  This is about the thickness of 2 business 

cards or playing cards.

    If  you  don’t  have  a  straightedge  or  feeler 

gauge  set  you  can  achieve  great  results  by 

pressing  one  of  your  outside  strings  down  at 

the  first  fret  and  24th  fret  and  having  a  friend 

slide  2  stacked  playing  cards  between  the  7th 

fret and the bottom of the string.  The 2 cards 

should slide under without lifting the string up.  

Adjust the truss rod accordingly.

MAINTENANCE AND ADJUSTMENTS FOR CARVIN BASSES

BRIDGE ADJUSTMENTS

    Each  Carvin  bass  is  set  for  best  possible 

playing  action  for  the  average  bassist.    We 

set  our  basses  up  for  3/32”  clearance  at  the 

24th fret.  If this dimension is much greater or 

less than this when you first receive your bass 

then  your  neck  will  probably  require  a  truss 

rod  adjustment.    Bassists  with  a  light  playing 

style can possibly lower the action slightly.  All 

bassist  with  a  hard  playing  style  wil   probably 

need  to  raise  the  action  slightly.    Use  a  1/16” 

allen wrench to raise or lower saddles.

CLEANING AND POLISHING

   

  For    al   Carvin  basses  with  a  gloss  finish, 

use  any good quality automobile wax or guitar 

polish.    To  avoid  scratching  the  finish  use  a 

clean  soft  cloth.    Do  not  get  wax  on  ebony  or 

rosewood fingerboards.

    For  Carvin  basses  with  the  natural  tung  oil 

finish,  apply  a  good  furniture  oil  such  as  “Old 

English”  lemon  oil  and  wipe  off  the  excess.  

This should be done at least twice a year.

  Ebony and rosewood fingerboards should be 

oiled with lemon oil twice a year.  

WARNING

• Your bass is constructed of seasoned solid wood 

and dried to specific moisture requirements.

•  If  you  live  in  a  desert,  high  mountain  or  a 

cold  winter  region,  you  wil   experience  dry 

and extreme weather conditions from time to 

time, which can cause your wood and finish 

to crack.  You can prevent cracking by storing 

your bass in it’s case and by not subjecting it 

to extreme heat or cold.

•  If  you  live  in  humid  regions  such  as  the 

Southeastern United States, or near the ocean, 

you  should  take  extra  precautions  and  keep 

your instrument in its case or gig bag as much 

as possible.

• Do not leave your bass and case in direct sunlight 

or in your car when it is hot.  Heat build up in the 

case can damage the instrument.

•  Carvin  does  not  warranty  cracks  or  neck 

warpage  due  to  extreme  weather  conditions, 

improper storage or misuse.

PREMIUM CARVIN TUNING KEYS

    Carvin premium bass tuners are designed to 

keep  your  Carvin  bass  in  perfect  tune.    They 

feature  a  very  smooth  feel  with  extra  fine  20:1 

gear  ratio.    You  can  adjust  the  tension  of  the 

Carvin tuning keys with the phil ips screwdriver.  

Just tighten or loosen the screw on the end of 

the button until the desired tension is obtained.

Tension

Adjustment

RECOMMENDED PICKUP HEIGHT

    After  you  have  the  neck  and  bridge  heights 

properly  adjusted  follow  these  recommend 

pickup clearances. All dimensions are measured 

from bottom of string to top of pickup.

PICKUP CHOICES:
-SP2 Soap bar humbucker neck 3/32”

-SP2 Soap bar humbucker bridge 1/16”

-H50S J-type humbucker neck 3/32” 

-H50S J-type humbucker bridge 1/16”

-J99 J-type Singlecoil neck 1/8” 

-J99 J-type Singlecoil bridge 3/32”

-HB2 Alnico 5 humbucker neck 5/32”

-HB2 Alnico 5 humbucker bridge 1/8” 

STRINGING YOUR BASS

You  have  the  choice  of  feeding  your  strings 

through the rear feed through holes on the back 

of the bass or through the T-slots on top of the 

bridge. Either way produces great tone. Pul  the 

string forward until the bal  end of the string comes 

to a stop.  Pul  the end of the string past the tuning 

key string post and cut the string so that it extends 

about 2” past the center of the string post.  Now 

stick the end of the string into the hole on top of 

the string post and wind it around the string post 

by turning the tuning key button. Keep the string 

wrapping underneath each prior wrap so that the 

final wrap is on the bottom of the post.

INTONATION  

Carvin  presets  the  string  saddles  for  accurate 

intonation.  Use your guitar tuner to fine tune your 

intonation.    With  the  aid  of  your  electronic  tuner, 

tune  each  string  to  the  proper  pitch.    Now  check 

your G string tuning at the 12th and 24th fret.  If 

the tuner shows sharp at the 12th or 24th fret, then 

adjust  the  G  string  bridge  saddle  slightly  further 

away from the neck.  If the tuner shows flat, adjust 

the saddle towards the neck.  Move the saddle 1/32” 

(about the thickness of a dime).  Retune the open G 

string perfectly and recheck the tuning at the 12th 

and 24th fret.  If the tuning is perfect, you are done 

intonating the G string.  If it is stil  sharp, then keep 

moving  the  string  saddle  further  away  from  the 

neck until your intonation is perfect.  Repeat this 

procedure for each string.

76-00005D  0808

12340 World Trade Drive, San Diego, CA  92128

(800) 854-2235

www.carvin.com

c

Intonation adjusting screw

#1 phillips screwdriver

Height adjustment screws 

1/16” allen wrench

Lockdown screw for side to side saddle adjustment 

1/16” allen wrench

0.555888s