Garmin echoMAP 50dv Installation Instructions
GPSMAP® 500/700 Series and
echoMAP™ 50/70 Series Installation
Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place will void the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
• Go to www.garmin.com/support and click Contact Support
for in-country support information.
• In the USA, call (913) 397.8200 or (800) 800.1020.
• In the UK, call 0808 2380000.
• In Europe, call +44 (0) 870.8501241.
Tools Needed
• Drill and drill bits
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (optional)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
Using the included hardware and template, you can mount the
device using one of two methods. You can use the included
bracket and hardware to bail mount the device, or you can use
the included template and hardware to flush mount the device in
the dashboard. If you want to mount the device using an
alternative method where it appears flat with the front of the
dashboard, you must purchase a flat-mount kit (sold separately,
with professional installation recommended) from your Garmin®
dealer.
When selecting a mounting location, observe these
considerations.
NOTE: Not all mounting methods are available for all device
models. See the specific mounting-type section for more details
about your model.
• The location should provide optimal viewing as you operate
your boat.
• The location should allow for easy access to all device
interfaces, such as the keypad, touchscreen, and card
reader, if applicable.
• The location must be strong enough to support the weight of
the device and protect it from excessive vibration or shock.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
• The location must allow room for the routing and connection
of all cables.
Bail Mounting a Five-Inch Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. Garmin recommends applying an anti-seize
lubricant to the screws before installing them.
You can use the included bracket to bail mount the device on a
flat surface. The five-inch models have the option of installing a
swivel at the base of the bail-mount bracket (Bail Mounting a
Five-Inch Device with a Swivel Base).
1 Using the bail-mount bracket
À
as a template, mark the pilot
holes
Á
.
2 Using a 1/8in. (3 mm) drill bit, drill the pilot holes.
3 Using the included screws
Â
, secure the bail-mount bracket
to the mounting surface.
4 Install the bail-mount knobs
Ã
on the sides of the device.
5 Place the device in the bail-mount bracket and tighten the
bail-mount knobs.
October 2014
Printed in Taiwan
190-01556-02_0C
Also See for Garmin echoMAP 50dv
Related Manuals for Garmin echoMAP 50dv
-
Garmin Discontinued nuvi 2417 Owner's Manual
22 pages
-
Garmin Discontinued nuvi 2457 Owner's Manual
22 pages
-
Garmin Discontinued nuvi 2508LTD Owner's Manual
22 pages
-
Garmin Discontinued zumo 660, NA Owner's Manual
52 pages
-
Garmin Discontinued nuvi 1450LM Owner's Manual
72 pages
-
Garmin Discontinued Appliance Data WFDE Prediction Program Instructions
20 pages
-
Garmin Discontinued Garmin Part 23 AML STC SA01933LA_D Instruction Manual
12 pages
-
Garmin Discontinued Garmin Part 23 AML STC SA01933LA_D Airplane Flight Manual Supplement
21 pages
-
Garmin Discontinued Garmin Rotorcraft HTAWS STC SR02080SE Airplane Flight Manual Supplement
14 pages
-
Garmin Discontinued Garmin Rotorcraft HTAWS STC SR02080SE Instruction Manual
22 pages
-
Garmin Discontinued Garmin Rotorcraft STC SR02232LA Instruction Manual
15 pages
-
Garmin Discontinued Garmin Part 23 AML STC SA01933LA_D Instruction Manual
29 pages
-
Garmin Discontinued Part 23 STC SA01692SE Instruction Manual
29 pages
-
Garmin Discontinued echoMAP 50dv Flush Mount Template
2 pages
-
Garmin Discontinued echoMAP 50dv Owner's Manual
48 pages
-
Garmin Discontinued echoMAP 70dv Flush Mount Template
2 pages
-
Garmin Discontinued echoMAP 70dv Owner's Manual
48 pages
-
Garmin Discontinued echoMAP 70dv Quick Start Manual
4 pages
-
Garmin Discontinued echoMAP 70dv Configuration Guide
2 pages
-
Garmin Discontinued echoMAP 70dv Flush Mount Kit Installation
28 pages
-
Garmin Discontinued DC 30 Dog Tracking Collar Owner's Manual
76 pages
-
Garmin Discontinued Edge 305 with Cadence Sensor Owner's Manual
94 pages
-
Garmin Discontinued Astro 220 (Handheld Only) Owner's Manual
12 pages
-
Garmin Discontinued Edge 305 with Cadence Sensor Battery Replacement Instructions
8 pages