GE 24957 GE Find It Lost Item Locators Owner's Manual

GE Remote Control Owner's Manual - 24957 GE Find It Lost Item Locators.
Download
Page  of 1
4.2, 1775 votes
background image

Your FIND IT ™ Locator Keyfob
requires only 3 simple steps to begin
using it:

1. Remove the battery tab.
2. Set the ITEM #.
3. Attach the Locator to an item.

 3. Attaching the FOFA

Each Keyfob includes a key ring. In addition, a
plastic lanyard or doublesided tape can also be used
to attach the Keyfob to any object that you could lose.

Using the Keyfob to Find Lost Items

To find a misplaced object with a Keyfob attached to
it, simply locate one of your other Keyfobs and press
the button corresponding to the missing unit (1 thru
6). If the object is in range, the Keyfob on the missing
object will begin to flash and beep. You can use any
Keyfob to locate any other Keyfob.

For best results, hold the Keyfob with the LED
pointing away from you. Walk around while trying to
find the item you’re looking for while repeatedly
pressing the appropriate button on the Keyfob.

Occasionally it may be necessary to press the number
on the Keyfob more than once even when the lost
item is within range due to interference or other
factors.

Keep the Keyfob away from large metal objects and
other radios sources that might reduce its range, as do
weak batteries.

Reduce or eliminate noises so you can hear the
beeping you are looking for.

The maximum distance the lost item can be from the
Keyfob is about 30 ft. Therefore, it may be necessary
to walk to various points in your home in order for it
to function.

Checking Your Setup

You can verify the ITEM # of each Keyfob by
pressing and holding the 5 and 6 keys simultaneously,
until the LED lights up, then release. The LED flashes
and beeps to indicate the ITEM #. For example, if the
Keyfob you are checking is defined as ITEM # 4, you
would hear 4 beeps.

FIND IT ™ Keyfob, Model K24945          P 1/2

FOFA K24945 1-2

FOFA K24945 2-2

FIND IT ™ Keyfob, Model K24945          P 2/2

2. Setting the ITEM #

FIND IT locators are expandable to 6 unique locators.

If you just inserted the battery, (or removed the
insulating tab) you are already in setup mode (LED
flashes continuously). To enter the setup mode at any
other time, press and hold the 1 and 3 buttons
simultaneously for about 3 seconds. A warble beep is
emitted and the LED flashes continuously.

To set the ITEM # for the Keyfob:

• Enter setup mode as above (LED flashing

continuously).

• Press a button (1 thru 6) to program the ITEM #.

The Keyfob beeps the number of times corresponding
to the ITEM #.

Important, if you also own a FIND IT Remote, and
you used the default code of 1 for it, then you will
need to set your Find IT Keyfobs to something other
than code 1, i.e. 2 thru 6.

Important Notes:

A Keyfob or a Remote cannot find a Remote or a
Keyfob that is set to the same code as itself.

After setting the ITEM #, wait about 20 seconds
before testing the Keyfob.

Removing the battery will cause your Keyfob to lose
its setting. You will need to reprogram it using the
steps above.

Care Instructions

- Do not allow the Keyfob to become wet. Wipe dry

immediately if it gets wet.

- It may be wiped with a damp cloth to clean.
- Handle with care. Do not drop.

The FCC wants you to know

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions: 1.
This device may not cause harmful interference; 2.
This device must accept any interference received,
including interference that may cause undesired
operation. This equipment generates and uses radio
frequency energy, and if not installed and used
properly, that is, in strict accordance with the
manufacturers instructions, it may cause interference
to radio and television reception. It has been type
tested and found to comply with the limits for remote
control devices in accordance with the specifications
in Sub-Parts B and C of Part 15 of FCC Rules, which
are designed to provide reasonable protection against
such interference in a residential installation.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause interference to radio or television
reception, which can be determined by unplugging
the equipment, try to correct the interference by one
or more of the following measures.

• Reorient the antenna of the radio/TV experiencing

the interference.

• Relocate the equipment with respect to the radio/TV.
• Move the equipment away from the radio/TV.
• Plug the equipment into an outlet on a different

electrical circuit from the radio/TV experiencing the
interference.

• If necessary, consult your local dealer for additional

suggestions.

The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modifica-
tions to this equipment. Such modifications could
void the user’s authority to operate the equipment.

1. Remove the Battery tab

Your Locator Keyfob comes with
one CR2032 type battery installed.
To active the unit, pull out the
plastic insulating tab:

The Keyfob will beep and
immediately go into setup mode.
The LED will begin flashing to
indicate that the Keyfob is ready to
be set up. Please see step 2: Setting
the ITEM #.

• Open the battery

compartment on
the back.

• Insert the battery

with the “+”
(positive) side up.

• Close the battery

compartment.

The Keyfob will beep and immediately go into setup
mode. The LED will begin flashing to indicate that
the Keyfob is ready to be set up. Please see step 2:
Setting the ITEM #.

To Replace the Battery:

Related Manuals for GE 24957 GE Find It Lost Item Locators

0.486942s