GE 57885 GE Motion Sensing Single Pole Switch (White) Owner's Manual

GE Accessories Owner's Manual - 57885 GE Motion Sensing Single Pole Switch (White).
Download
Page  of 2
4.1, 1503 votes
background image

 Single Pole Motion Sensing Switch

WARNING: For indoor use only. The Single Pole Motion Sensing Switch 

detects motion to turn on lights for an adjustable amount of time. A built-in 

photo cell can be set to keep lights off when the lights aren't needed. The 

unit has excel ent sensitivity and a wide 150˚ detection range. It can be used 

with incandescent lighting as well as rapid start fluorescent lighting.

Instal ation is as easy as replacing a wall switch. However, some codes 

require instal ation by a qualified electrician.

Features include:
150˚ motion detection angle.
Adjustable on-time from 5 sec. to 20 min.
Adjustable photocel .
Works with incandescent and rapid start 

fluorescent lighting.
Works with motors up to 1/8 hp.
Slide switch selectable OFF, ON AND AUTO modes.
Included are:
The sensor switch 
Cover plate 
3 wire connectors 
2 large screws 
2 smal  screws.

INSTALLATION

1. SELECT A LOCATION

New Application

Choose a location where the motion sensor has 

a clear view of the entire area where occupant 

motion may occur.

Retrofit Application

Motion sensing switch will replace existing wall 

switch. Use only where the existing switch location 

provides a clear view of the occupied area.

General Application Information

The detector is more sensitive to motion across the front of the sensor 

than to motion towards the sensor. The detector senses heat in motion 

and possible heat sources that change temperature quickly. Therefore, to 

avoid false triggering, avoid placing the sensor where it will be aimed at air 

conditioners, heaters, and other sources of heat or cold.

2. INSTALLING THE SWITCH

If you are unsure or uncomfortable about performing this instal ation, 

consult a qualified electrician. WARNING: Turn power off at the circuit 

breaker before wiring.

Remove the decorative coverplate (secured by two screws).
Remove Control Cover. (Press 

in with screwdriver. Swing out 

cover to remove.)
Remove the existing switch (if 

this is a retrofit application).
Connect the detector as 

shown in the diagram.  Before 

instal ing the detector into the 

box, 

make sure there is no wire 

exposed at the connection.

Typical Installation

Mount the detector into the wall 

box with the mounting screws.
For test purposes, use a small 

screwdriver to turn the time 

control ful y counter-clockwise and the light control ful y clockwise. Turn the 

power back on at the circuit breaker.










Set the switch to the AUTO mode. When unit stabilizes (about 1 minute) the 

light may flash 3 times indicating the sensor is ready to detect motion. If 

motion is detected, the lights wil  turn on. The lights wil  turn off 5 seconds 

after motion is no longer detected.

3. ADJUST TIME & LIGHT SENSITIVITY

Time

The length of time that the lights 

stay on is adjustable from 5 

seconds to 20 minutes. Use a 

small phil ips screw driver to set 

the time by using the diagram as 

a guide.

Light Level

The sensor can be prevented 

from turning on lights when 

there is already enough light in 

the room. Use a small phil ips screw driver to set the light level using this  

diagram as a guide. In the ful y clockwise position, the sensor turns on lights 

even in full daylight. In the ful y counter-clockwise position, the sensor only 

turns on lights when the surrounding light level is very low.

To adjust the photocell:

When the light in the room is at the level you want the lights to turn on, set 

the switch to the AUTO position.
Put the TIME control to the 5 sec. (fully counter-clockwise) position.
Put the LIGHT control to the minimum dark (fully counter-clockwise) 

position. Wait for the lights to turn off.
Turn the LIGHT adjustment clockwise in very small steps and wait 2 

seconds before moving your hand in front of the sensor. Repeat until the 

lights controlled by the sensor come on. The light will now come on when 

the light level is at or below the present level and motion is detected.

4. FINISH INSTALLATION 

Replace control panel cover and install the decorative wall plate. In 

instal ations where the motion sensor switch is combined with other 

switches or outlets on an expanded box, a combination wall plate will need 

to be purchased. Various combination wall plates are available at Home 

Centers and Electrical Supply Stores. 

 

Slide the switch a couple of times to make sure it operates freely.

USE

MODE SELECTION SWITCH

Moving the switch selects one of three modes of operation: OFF, AUTO, ON

OFF: Lights stay off.
AUTO: Lights come on for time set when motion is detected and the light 

level is below the set level.
ON: Lights stay on continuously.

TROUBLESHOOTING

Light does not come on.

Circuit breaker or fuse is turned off.
If the lamp being control ed has another switch, it may be turned off.
Bulb is defective.
LIGHT control is set too far toward the DARK position.
MODE switch is set to OFF instead of AUTO.
Poor connection.

Lights do not stay on in the Auto mode.

Motion has stopped in the room.
TIME control is set for too short a delay.

Light does not turn off.

Incorrect wiring.
MODE switch is set to ON instead of AUTO.
Motion is stil  present.
Delay set by TIME control has not expired.

Light comes on for no reason in the Auto mode.

Heating or cooling objects (such as air vents, appliances, or drafts through the wal  box) are 
causing false triggering.
Switch on the sensor has been turned off and back on.
There was a momentary power interrup-tion. The light wil  turn off automatical y when the "on" 
time expires.

SPECIFICATIONS 

Electrical input: 120V, 60 Hz

Fluorescent Load: (2 tube minimum) 30 Watt minimum 400 Watt maximum Rapid Start

Motor Load: 1/8 HP maximum

Incandescent: 500W maximum

On-Time: Adjustable approximately 5 sec. to 20 min.

Photocell Sensor: From full daylight to less than 1 FC.

Coverage: up to 15 ft. at 150˚, up to 30 ft. in front of the sensor

Questions? Visit us at www.jascoproducts.com

1.

2.
3.

4.












OFF

Related Manuals for GE 57885 GE Motion Sensing Single Pole Switch (White)

0.580581s