GE BoxTimer GE Time Switch (15251, 15252 and 15253) Quick Start Manual
SPECIFICATIONS
Input Voltage: 120 VAC, 208/240 VAC, or 277 VAC in all units based upon
dipswitch configuration.
15252
NEMA3R Indoor&Outdoor BM-A301US5-O2
15253,15251
NEMA1 Indoor
BM-A301US5-I2
15250
NEMA3R Indoor&Outdoor EM-A301US9-O2
SwitchRating:DPDTModels
NormallyOpenContacts
40A Resistive, 120-277Vac.
30A General Purpose, 120-277Vac.
20A Resistive, 30Vdc
1 HP, 120Vac ; 2HP, 240Vac
20A Ballast, 120-277Vac.
15A Tungsten, 120Vac
800VA, Pilot Duty, 120Vac.
720VA, Pilot Duty, 240Vac.
TV-5, 120Vac
NormallyClosedContacts
30A Resistive, 120-277Vac
15A General Purpose, 120-277Vac
15A Resistive, 30Vdc
20A Ballast, 120-277Vac
1/4HP, 120Vac; 1/2HP, 208-240Vac.
290VA, Pilot, 120Vac.
360VA, Pilot, 208-240Vac.
NOTE: If loads are connected to both NC and NO contacts, both contacts are
derated to 67% of the above values.
ENVIRONMENTALRATINGS
Ambient Temperature: –40F to 130F
Humidity: 0-95% RH, Non-condensing
WIRINGCONNECTIONS
Screw clamp terminals for up to 2 AWG #8 wires
per position. For supply connections, use 8AWG or larger wires suitable for at
least 105° C. Use copper conductors only.
LIGhTS
Power LED (Orange) – Light illuminates when power is applied to
the timer
Status LED (Green) – Light illuminates when power is applied to load.
INSTALLATION
CAUTION: Before wiring or service, power to this time switch and the
equipment it controls must be turned off. Turning off the timer switch only
will not prevent a shock hazard. Replace cover plate within housing before
supplying power to time switch. Installation should be performed by a licensed
electrician only. Before installing this product read all instructions carefully.
Remove protective cover panel within time switch housing by removing
screws located above timer face and at the bottom of the cover panel.
DIPSWITChCONFIGURATION
WARNING: Failure to properly configure the dipswitch will result in
damage to the unit and void the warranty! Before installing and wiring the GE
Time Switch, proper configuration must be selected. This is accomplished as
follows:
INPUTVOLTAGEDIPSWITChSETTING:
1.
Do not apply power to the timer prior to setting correct Input Voltage DIP
switch.
2.
Determine the input voltage which will be applied to the timer (i.e. L1 and
L2/N terminals, see wiring diagrams)
3.
Set the DIP switch according to the diagram below.
NOTE: Unit is shipped with DIP switches set for 277VAC Input Voltage
CAUTION: Do not check circuits by “sparking” wires to terminals. Damage to
the timer may result.
NOTE:For outdoor locations (model GE 15252), rain tight or wet location
conduit hubs that comply with requirements of UL 514B (standard for fittings
for conduit and outlet boxes) must be used.
1.
Remove 2 screws retaining the interior cover panel and remove panel
by prying out with a thin blade at the top.. Select knockouts to be used.
Remove the inner 1/2” knockout by inserting a screwdriver in the slot
and carefully punch knockout loose. Remove slug. If the 3/4” knockout
is required, remove the outer ring with pliers after removing the 1/2”
knockout. Smooth edges with knife if necessary.
2.
Place enclosure in desired mounting location and mark the three
mounting holes.
3.
Drill holes for #10 screws, start screws in holes.
4.
Place enclosure over screws and tighten screws.
5.
Connect conduit hubs to conduit before connecting the hubs to the
enclosure. After inserting hubs into enclosure, carefully tighten hub lock
nut. Do not over-tighten.
DipswitchSettingcontinued:
6.
Install in accordance with all applicable National and Local code
requirements. See Figure 1 and wiring diagrams.
7.
Replace interior cover panel and 2 screws.
TimeSwitch
15251/15253
Indoor
NEMA 1-Rated Enclosure
15252
Indoor/Outdoor
NEMA 3R-Rated Enclosure
120VAC
277VAC (Default)
208~240VAC
NOTE: Unit is shipped with DIP Switches set for 277VAC Input Voltage.
CAUTION: Do not check circuits by “sparking” wires to terminals. Damage to
the timer may result.
INPUT VOLTAGE DIP SWITCH SETTING:
1. Do not apply power to the timer prior to setting correct Input Voltage DIP switch.
2. Determine the input voltage which will be applied to the timer (i.e. L1 and L2/N terminals,
see wiring diagrams).
3. Set the DIP Switch according to the diagram below.
Related Manuals for GE BoxTimer GE Time Switch (15251, 15252 and 15253)
-
GE Timers 15142 Outdoor Digital Timer Owner's Manual
2 pages
-
GE Timers 15143 Outdoor Lighting Timer Owner's Manual
4 pages
-
GE Timers 15150 GE 7Day Digital Timer Owner's Manual
1 pages
-
GE Timers 15265 InWall Digital Timer Owner's Manual
2 pages
-
GE Timers 15267 PlugIn,24 hour Mechanical Timer Owner's Manual
1 pages
-
GE Timers 15270 PlugIn Digital Timer Owner's Manual
2 pages
-
GE Timers 15273 PlugIn GE 7Day Digital Timer Owner's Manual
2 pages
-
GE Timers 15312 Sun Smart Digital Timer Quick Reference Guide
2 pages
-
GE Timers 15313 GE 7Day InWall Digital Timer Owner's Manual
2 pages
-
GE Timers 15318 Push Button Countdown Timer Owner's Manual
1 pages
-
GE Timers BoxTimer 15132 GE Digital Time Switch Owner's Manual
3 pages
-
GE Timers BoxTimer GE Time Switch (15087, 15207 and 56922) Owner's Manual
2 pages
-
GE Timers InWall 15071 GE Smart Digital Timer Owner's Manual
1 pages
-
GE Timers InWall 15086 GE Smart Digital Timer Owner's Manual
1 pages
-
GE Timers Outdoor 15112 Mechanical Countdown Timer Owner's Manual
1 pages
-
GE Timers PlugIn 15075 Mechanical Timer Owner's Manual
1 pages
-
GE Timers PlugIn 15076 Mechanical Timer Owner's Manual
1 pages
-
GE Timers PlugIn 15091 GE 7Day Digital Timer Owner's Manual
1 pages
-
GE Timers PlugIn 15119 24 hour Mechanical Timer Owner's Manual
1 pages
-
GE Timers PlugIn 15151 Mechanical 7Day Timer Owner's Manual
1 pages
-
GE Timers PlugIn 15152 Mechanical Timer Owner's Manual
1 pages
-
GE Timers PlugIn Digital Timer 15079 Owner's Manual
2 pages
-
GE Timers PlugIn Digital Timer 15089 Owner's Manual
2 pages
-
Intermatic Timers SS7C User's Manual
2 pages