GE InWall 15084 Mechanical Countdown Timer Owner's Manual

GE Timers Owner's Manual - InWall 15084 Mechanical Countdown Timer.
Download
Page  of 1
4.6, 1060 votes
background image

ADVERTENCIA

Riesgo de choque eléctrico
• Corte la corriente antes de efectuar 

una instalación

• No lo use en lugares húmedos
• Use solamente en interiores
Riesgo de incendio
• No exceda los límites eléctricos 

permitidos

• Utilícelo con alambre de cobre 

únicamente

WARNING

Risk of electric shock
• Shut of  power at fuse box or circuit 

breaker before instal ation

• Do not use in wet locations
• Use indoors only
Risk of fire
• Do not exceed electrical ratings
• Use copper wire only with this device

125VAC, 15A Resistiva
125VAC, 15A Servicio General
125VAC, 1250W Tungsteno
125VAC, 1/2 HP (caballo)

FÁCIL INSTALACIÓN:

Antes de la instalación, apague la alimentación en la caja de fusibles o disyuntor.

NOTA: Para uso con aplicaciones de un interruptor unipolar instalado de forma 

permanente.

1. Retire la placa de pared y el interruptor unipolar, si existe.
2. Mediante un pequeño destornillador de punta plana, apalanque suavemente la cubierta frontal de 

temporizador de pared para soltarla de la unidad principal del temporizador; deje a un lado la cubierta para 
utilizarla más adelante.

3. Pele 3/ 8 pulg. de aislamiento del cable de construcción. 
4. Conecte los cables mediante los conectores de rosca que se suministran (use con alambre de cobre 

únicamente). El cable conductor NEGRO al conductor caliente línea del circuito; El cable conductor ROJO al 
conductor carga línea del circuit; El cable conductor BLANO al conductor Neutro línea del circuito. (A menudo 
el cable neutro se encuentra contra la parte posterior de la caja del interruptor, unido a una tuerca para 
cable. Si no está seguro de cuál cable es cuál o no puede localizar el cable neutro, consulte a un electricista 
certificado). CONSULTE el diagrama de cableado).

5. Si se conectó un cable de conexión a tierra al interruptor antiguo, coloque un conector de rosca sobre el extremo del 

cable a tierra y empuje el conector y el cable a tierra hacia la parte posterior de la caja.

6. Monte el temporizador de forma segura con los tornillos largos de montaje que se suministran. Coloque la cubierta 

nuevamente ajustándola contra la unidad del temporizador principal.

7. Restablezca la energía en la caja de fusibles o disyuntor.

OPERACIÓN:
El cronizador tiene tres posiciones: ON (activado), OFF (de-activado) y TIMER (cronizador). Para controlar la carga 
manualmente ponga el conmutador corredizo en la posición “ON” o “OFF”. Para utilizar el cronizador:
1. Poinga el conmutador deslizante en la posición “TIMER”.
2. Gire el cuadrante en sentido de reloj hasta que el tiempo deseado se acople con la flechita en el centro del cuadrante.

125VAC, 15A Resistive
125VAC, 15A General Purpose
125VAC, 1250W Tungsten
125VAC, 1/2 HP

EASY INSTALLATION:

Shut off power at fuse box or circuit breaker before installation.

NOTE -For use with single-pole, one switch permanently installed applications.

1. Remove wall plate and existing single pole switch, if applicable.

2. Using a small flat blade screwdriver, gently pry off the front cover plate of in-wall timer from the

main unit of the timer; set cover plate aside for later use.

3. Strip building wire to 3/8”.

4. Connect wires using the provided twist-on connectors (Use with copper wire only). BLACK lead to 

circuit’s (HOT) line conductor; RED lead to circuit’s Load conductor; White lead to circuit’s Neutral 

conductor. (Often the Neutral wire can be found pushed in the back of the switch box, bound by a wire 

nut. If you are uncertain as to which wire is which or cannot locate your neutral wire, please consult a 

certified electrician.)

REFER to the wiring diagram.

5. If a ground wire was connected to the old switch, put a twist-on connector on the end of the ground wire and push the connector 

and ground wire into the back of the box.

6. Mount the timer securely with long mounting screws provided. Reattach cover plate by snapping on to the main timer unit.

7. Restore power at fuse box or circuit breaker.

OPERATION:

The timer has 3 settings ON, OFF, and TIMER. To control the load manually, place the slide switch in the “ON” or “OFF” position. To use 

the timer,

1. Place the slide switch in the “TIMER” position

2. Rotate the dial Clockwise until the desired time lines up with the arrow in the center dial.

= Wiring Nut

Typical Wiring Schematic

Black

Black

Light

White

White

White

Red

Timer

120 VAC

Power

Source

LOAD

LINE

GROUND
[GREEN or BARE]

NEUTRAL
[WHITE]

LINE
[BLACK]

LOAD
BLACK In-Wall
Red on Timer

15067
15068
15069
15081
15082
15084

Manual Version 2

12-31-2009

www.jascoproducts.com

= Tuercas para cable (empalmes plásticos)

Esquema de cableado típico

Negro

Negro

Luz

Blanco

Blanco

Blanco

Rojo

Temporizador

Fuente de

alimentación

120 VCA

CARGA

Línea

A TIERRA
[VERDE or DESNUDO]

NEUTRO
[BLANCO]

Línea
[NEGRO]

CARGA
NEGRO En Pared
Rojo en Temporizador

Related Manuals for GE InWall 15084 Mechanical Countdown Timer

0.491796s