Netgear MBR624GU Installation Guide

Netgear 3G/4G LTE Routers Installation Guide - MBR624GU.
Download
Page  of 2
4.2, 1199 votes
background image

)NSTALLATION'UIDE

3G Mobile Broadband Wireless Router MBR624GU

Your wireless 3G/UMTS USB modem (sold separately) must be activated before you 
install the router. For a list of compatible wireless USB modems, see the NETGEAR 
website at http://www.netgear.com/3G. To configure the router during installation, you 
need a computer with an Ethernet port. Your computer must be configured with DHCP 
(most PCs are).

Package Contents

3G Mobile Broadband Wireless Router

USB docking station

Power Adapter

Snap-on router stand

Resource CD

Connecting the 3G/UMTS USB Modem
1.  
At the location where you will install 

the router, connect your activated 3G/
UMTS USB modem to your 
computer. Follow the instructions 
from your Internet Service Provider 
(ISP) to connect to the Internet from 
your computer.

2.  Verify that you can connect to the 

Internet. Then, close the software 
that you used to connect to the 
Internet.

3.  Place the router in its vertical stand, 

and adjust the antenna. For best 
performance, place the router in a 
location where your 3G/UMTS USB 
modem Internet connection is strong, 

such as on a desk near a window instead of on the floor.

4.  Connect your wireless 3G/UMTS USB modem with activated Internet service to the 

USB port on the rear panel of the router using a USB cable or docking station.

5.  If your wireless 3G/UMTS USB modem has a separate antenna, adjust it as needed.

Connecting Your Router
1.  
Connect one end of the Ethernet cable that came with your router into a LAN port on 

the router, and the other end into the Ethernet port of your computer.

2.  Plug in the power adapter to your router, and push the Power button on the rear panel.

3.  Verify that the following LEDs on the front 

of the router light up: 

 Power. Power is supplied to the 

router.

 LAN. Your computer is securely 

connected to this LAN port on the 
router.

 USB. Your wireless USB 

modem is securely connected to the 
router.

 Wireless. There is a wireless 

signal from the router.

 Internet. This LED is red because the router is not connected to the 

Internet.

Configuring Your Router’s Internet Connection
1.  
From the Ethernet connected computer, open a Web browser.

2.  Connect to the router by typing http://192.168.0.1 or http://www.routerlogin.com in 

the address field of your browser.

The Setup Wizard Welcome screen displays.

Note: When you connect to the router after initial configuration, a login prompt will 
display instead of the Welcome screen (see “Logging in to Your Router after Initial 
Configuration” on the ot
her side of this document). 

3.  Click Next. Depending on your location, the Setup Wizard either: (a) automatically 

configures your router’s Internet connection, or (b) prompts you for the following 
information:

Select both the country where you are located and your ISP from the pull-down 
menus. (If required by your ISP, you may also be prompted for your Login and 
Password.) If your ISP is not listed, select Other. 

If you selected “Other”, you will be prompted for the following:

Your Login and Password, if required by your ISP.

The APN/ISP Network Name.

Select your Packet Data Protocol (PDP) Type from the pull-down menu.

If your 3G/UMTS USB modem has a SIM card, you may be prompted for its PIN 
code. 

Click Next.

You now will be prompted to configure your Wi-Fi network.

Also See for Netgear MBR624GU

0.575710s