RCA MAF130BK Installation Manual

RCA Video Installation Manual - MAF130BK.
Download
Page  of 2
4.8, 1596 votes
background image

2.  With the help of another person, place the mount 

against the wall and level it using the bubble guide.

3.  While another person holds the mount in place, mark 

four locations (two per stud) on the wall where the 

mount is to be installed. Be sure to use the center of 

each stud.

4.  Set the mount aside and drill a 1/4” (6 mm) pilot hole at 

each marked location.

5.  Place the mount back against the wall and secure 

it using the Lag Bolts (Q) and Lag Bolt Washers (R) 

provided (see Fig. 1). Do not over-tighten these bolts 

and do not release the mount until all bolts are in 

place.

Part 1b – Mounting the Wall 

Plate (Concrete)

Part 2 - Attaching the Arms  

to the Display

Warnings

1.  Make sure these instructions are read and thoroughly 

understood before attempting installation. If you 

are unsure of any part of this installation, contact a 

professional installer for assistance.

2.  The wall or mounting surface must be capable of 

supporting the combined weight of the mount and the 

display; otherwise the structure must be reinforced.

3.  Safety gear and proper tools must be used. Failure to 

do so can result in property damage and/or serious 

injury.

4.  A minimum of two people are required for this 

installation. Do not attempt to install this mount alone 

under any circumstance.

5.  Follow all instructions and recommendations 

regarding adequate ventilation and suitable locations 

for mounting your display. Consult the owner‘s 

manual for your display for more information

Hardware Kit

(Ref) Item (Qty)

Bag#

1

2

3

4

5

6

(A) M4x12 Bolt (x4)

(B) M4x30 Bolt (x4)

(C) M4 Lock Washer (x4)

(D) M5x12 Bolt (x4)

(E) M5x30 Bolt (x4)

(F) M5 Lock Washer (x4)

(G) M6x12 Bolt (x4)

(H) M6x35 Bolt (x4)

(I) M6 Lock Washer (x4)

(J) M8x16 Bolt (x4)

(K) M8x40 Bolt (x4)

(L) M8 Lock Washer (x4)

(M) Small Spacer (x4)

(N) Large Spacer (x4)

(O) M6 Washer (x4)

(P) Concrete 

Anchor (x4)

(Q) M8x63 

Lag Bolt (x4)

(R) M6 Lag Bolt 

Washer (x4)

Important! For safety reasons, the concrete wall must be 

capable of supporting the combined weight of the mount 

and display.
1.  With the help of another person, place the mount 

against the wall and level it using the bubble guide.

2.  While another person holds the mount in place, mark 

four locations on the wall where the mount is to be 

installed.

3.  Set the mount aside and drill a 7/16” (11 mm) pilot hole 

at each marked location. Remove any excess dust from 

the holes.

4.  Insert a Concrete Anchor (P) into each hole so that it is 

flush with the concrete surface. A hammer can be used 

to lightly tap the anchors into place if necessary. 

NOTE: If the concrete wall is covered by a layer of plaster 

or drywall, the concrete anchor must pass completely 

through the layer to rest flush with the concrete 

surface.

5.  Place the mount back against the wall and secure 

it using the Lag Bolts (Q) and Lag Bolt Washers (R) 

provided (see Fig. 1). Do not over-tighten these bolts 

and do not release the mount until all bolts are in 

place.

Fig.1 Attach the wall 

plate to the wall.

Important! Use extra care during this part of the 

installation. If possible, avoid placing your display 

facedown as it may damage the viewing surface.
NOTE: Your mount comes with a selection of bolt 

diameters and lengths to accommodate a wide variety of 

display models. Not all of the hardware in the kit will be 

used.
1.  Determine the correct length of bolt to use with your 

display by first examining the back of your display.

A.   If your display has a flat back, you will use one of the 

shorter bolts (A, D, G, or J) from the hardware kit.

B.    If your display has a curved or recessed back, you will 

use one of the longer bolts (B, E, H, or K) along with    

a spacer (M or N).

For displays with flat backs. .

For displays with curved or
recessed backs

Fig. 3 - Use a longer bolt and spacer for displays with 

curved or recessed backs. Do not use the M6 Washer 

(O) if you are using the M8 Bolts (J or K).

Part 3 - Final Installation and 

Adjustment

Tools Required
Phillips Head Screw Driver

Ratchet or Driver with 1/2” (13 mm) Socket

Electric Drill

1/4” (6 mm) Drill Bit and Stud Finder for Drywall 

Installation

7/16” (11 mm) Masonry Bit for Concrete Installation

1.   With the help of another person, carefully lift your 

display and place it on mount (see Fig. 4). Place the 

display in the middle of the mount, and do not release 

the display until the mounting arms have securely 

hooked onto the crossbars.

2.  Move the safety tab located on each arm into position 

to avoid having the display accidentally lifted from the 

mount. A padlock can be inserted into one of the tabs 

to help prevent theft of your display (see Fig. 5).

3.  The cable management clips can be used to keep your 

power cord and other cables in order.

4.  Side-to-side and front-to-back adjustments can be 

made by firmly grasping your display and carefully 

moving it to the desired position. 

5.  If any of the arms become too lose to hold their 

position, they can be tightened using the Alley Key 

provided in your hardware kit (see Fig. 6).

6.  To adjust the tilt position of your display, have one 

person hold the display in place while another person 

loosens the two tilt adjustment knobs located on either 

side of the mount (see Fig. 7). Once the knobs are loose, 

move the display to the desired angle. Tighten the 

knobs securely before releasing the display.

7.  If you find that your display is not level, first loosen 

the horizontal adjustment screw located behind the 

mount (see Fig. 8) using the Allen Key provided in 

your hardware kit. Carefully level your display and 

re-tighten the adjustment screw.

2.  Determine the correct diameter 

of bolt to use by carefully trying 

one bolt each from Bags 1 - 4 of the 

hardware kit. Do not force any of 

the bolts – if you feel resistance 

stop immediately and try a smaller 

diameter bolt.

3.  Attach the arms to the back of your 

display using the bolts identified 

in Steps 1 and 2 along with the 

corresponding Lock Washer (C, F, 

I, or L) (see Fig. 2 and 3).

A.   If you are using the M4, M5, or M6 

bolts (Bags 1, 2, and 3 respectively), 

you will also need to use the M6 

Washers (O).

B.    If you are using one of the longer bolts on a display 

with a curved or recessed back, you will also use a 

Spacer (M or N). Use the Smaller Spacer (M) for M4 and 

M5 bolts and the Large Spacer (N) for M6 and M8 bolts.

4.  Make sure all screws are secure, but do not over-

tighten them.

Fig. 2 - Attach the 

arms to the back 
of your display

Fig. 4 - Carefully hook the 

display onto the wall 

plate.

Fig. 5 - A small padlock 

can be used to help 

prevent theft of your 

display.

Fig. 6 - Use the Alley Key 

to tighten the arms 

and prevent unwanted 

movement.

Fig. 7 - Loosen the 

adjustment knobs to 

change the tilt angle. 

There is one knob 

on each side of the 

mount.

Audiovox Electronics Corporation (the “Company”) warrants to you the 

original retail purchaser of this product that should it, under normal use 

and conditions, be proven defective in material or workmanship during 

its lifetime while you own it, such defect(s) will be repaired or replaced 

(at the Company’s option) without charge for parts and repair labor. 

To obtain repair or replacement within the terms of this Warranty, the 

product is to be delivered with proof of warranty coverage (e.g. dated bill 

of sale), specification of defect(s), transportation prepaid, to the Company 

at the address shown below. Do not return this product to the Retailer.

This Warranty does not cover product purchased, serviced or used 

outside the United States or Canada.

This Warranty is not transferable and does not extend to costs incurred 

for installation, removal or reinstallation of the product. This Warranty 

does not apply if in the Company’s opinion, the product has been 

damaged through alteration, improper installation, mishandling, 

misuse, neglect, or accident. THE EXTENT OF THE COMPANY’S 

LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR 

OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL 

THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID 

BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY 

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY 

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY. 

IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY 

CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. No 

person or representative is authorized to assume for the Company any 

liability other than expressed herein in connection with the sale of this 

product. Some states/provinces do not allow limitations on how long 

an implied warranty lasts or the exclusion or limitation of incidental or 

consequential damage so the above limitations or exclusions may not 

apply to you. This Warranty gives you specific legal rights and you may 

also have other rights which vary from state/province to state/province.

U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,  

Hauppauge, New York  11788

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, 

Unit 3, Door 16, Mississauga, Ontario  L5T 3A5
Trademark(s) Registered Marcas Registradas. 

All other brands and product names are trademarks or registered 

trademarks of their respective owners.
© 2008 Audiovox Accessories Corporation 

111 Congressional Blvd., Suite 350 

Carmel, IN 46032
www.rca.com 

MAF130BK_US_IB_00

 Limited Lifetime Warranty

Keep your sales receipt to obtain warranty parts and 

service and for proof of purchase. Attach it here and record 

the serial and model numbers. These numbers are located 

on the product.

Model No. __________________________________________

Serial No. ___________________________________________

Purchase Date: ______________________________________

Dealer/Address/Phone  ______________________________

Important! For safety reasons, this mount must be 

secured to two adjacent wood studs whose centers are 16 

inches apart (16" on center). The studs must be capable of 

supporting the combined weight of the mount and display.
1.  Using a stud finder, locate and mark two adjacent studs 

for securing the mount. 

Part 1a - Mounting the Wall 

Plate (Drywall)

Fig. 8 - Use the Alley 

Key to loosen the 

horizontal adjustment 

screw and level your 

display.

LCD/Plasma TV Wall Mount

Installation Manual

0.657049s