Westinghouse Outdoor Lighting Fixture User's Manual

Westinghouse Lawn and Garden Equipment User's Manual - Outdoor Lighting Fixture.
Download
Page  of 1
4.3, 2024 votes
background image

 

          is the registered trademark of The Stanley Works and Subsidiaries. Produced under license by The NCC.

Distributed byThe NCC, Inc., Brooklyn, NY 11220  • www.thencc.com • MADE IN CHINA 

Ni-MH

Ni-MH battery included.
10Min Charge retains program for up to 1 months.
Full charge retains for more than 2 months.

15Ft. (4.5m) AWG 12/3 SJTW
Rated 125V/15A/1875W/60Hz

Contains  Ni-MH  (nickel  metal  hydride)  battery.  Battery 

must be recycled or disposed of properly.
Customer Service Assistance: Toll Free 1-800-730-3707

To Use Photo Cell Timer   
Slide Switch To “Photo Cell”

 Push the “Mode” button once. You will see the words 

“On At Dusk, OFF 0:00 At Dawn.” This means that 

the  plugged-in  devices  will  power  ON  when  it  gets 

dark, and will power OFF at sunrise.

  Push  the  “Photo  Set”  button  repeatedly  to  cycle 

through the different Dusk to Dawn options. You may 

have your devices turn ON at Dusk, and turn OFF from 

1 to 12 hours after dusk.

 

Push  the  “Mode”  button  once  to  finish  program-

ming. It is okay if the current time displayed is not 

correct; the Photocell timer will still work correctly. If 

desired, you may set the current time by following the 

instructions to the left.

Manual On/Off
The timer can be manually turned On or Off
as desired.
•  Push the ON/OFF/AUTO button to change the current

  mode to On, Off, or Auto (follow the timer settings).

Packaging and Use Instructions
General: 
An outdoor seasonal-use cord-connected wiring device shall contain all of the following or equivalent statements (following the word CAUTION) on the

outer surface of the smallest unit package or on a stuffer sheet or tag (or its equivalent):

 CAUTION – Risk of Fire. Not for permanent installation. Use only with a total of 12 Ampere maximum Christmas-tree or other seasonal lighting products. Do not 

install or use this product for more than a 90-day period.

 If using Christmas tree or decorative-lighting products that are not marked with an ampere rating, connect no more than 140 screw-base lamps (C7 or C9) or 12 

strings with midget (pushin) lamps to this cord set.

 Cord sets shall be plugged into a GFCI-protected receptacle.

 If using an outdoor-use cord set for an extended period of time (greater than 90 days) please consider hard wiring a permanent outdoor-use receptacle rated for 

year-round use in the area that power is needed. Please contact a Licensed electrician for proper installation of permanent wiring.

 After completion of installation, the connector shall be maintained a minimum of 6 inches above ground.

 For temporary outdoor installation and use - Not to exceed  90 days

To Use Digital Timer   
Slide Switch To 
Timer
To Set the Current Time        While time appears in the LCD.

 Push “Set Time” button once. The time display will be flashing. (If the display stops flashing 

before you finish, just push “Set Time” again to continue.)

 Push the “Day” button until the current day appears on top.

 Push the “Hour” button until the current hour appears. Be sure to cycle through the hours until 

AM or PM appears to the right of the time.

 Push the “Min” button until the current minute appears. (Holding the “Min” button down will 

make the minutes advance rapidly.)

 Push the “Set Time” button to finish the program – the display will stop flashing. (If it stops 

flashing before you push the button, that’s okay.)

To Set Program
Slide Switch To “Timer”
- be sure to set the current time first (see left)

 Push the “Mode” button once. The words “Program #1 ON” will appear. We will now set the 

time for your plugged-in devices to turn ON.

 Push the “Set Time” button once. The time display will be flashing. (If the display stops 

flashing before you finish, just push “Set Time” again to continue.)

 All of the days of the week will appear on top. This means that the On/Off times you set will 

run every day of the week. To have the program run only on specific days, push the “Day” 

button to cycle through the different day options. The choices in order are:

 Push the “Hour” button until the desired ON hour appears. Be sure to cycle through the hours 

until AM or PM appears to the right of the time.

 Push the “Min” button until the desired ON minute appears.

 Push the “Set Time” button to finish the program - the display will stop flashing. (If it stops 

flashing before you push the button, that’s okay.)

 Push the “Next Program” button. The words “Program #1 OFF” will appear.

 Repeat  -  to set the OFF time.

 Push the “Mode” button to finish the program and return to the current time.

     You are now finished setting Program #1.  To set additional programs, push “Mode” to enter 

the  programming  mode  and  then  “Next  Program”  to  reach  Program  2,  3,  etc.  Up  to  6 

programs can be entered.

NOTE: The digital timer turns On and Off when the current time matches the time you set in the 

program, and is not retroactive. This means that if the current time is 5pm and you set the 

timer to turn ON at 4pm, the program will not run until tomorrow at 4pm.

NOTE: To set up Timer for the first time, plug in the timer for 10 minutes, then push the “Reset” button to clear all settings.

MO TU WE TH FR SA SU  -  al  the days of the week
MO TU WE TH FR SA  -  Monday through Saturday
MO TU WE TH FR  -  Monday through Friday
SA SU - Saturday and Sunday only

MO   Monday Only
TU    Tuesday Only
WE –  Wednesday Only
TH  –  Thursday Only

FR  –  Friday Only
SA  –  Saturday Only
SU  –  Sunday Only

6-Outlet Yard Stake with Dual Timers
All Weather 6-Outlet Safety Power Station

with Digital Photocell Timer & Programmable 7 Day Digital Timer 

Interactive Programming & Operating Tutorial

available online at:

 www.thencc.com

 

0.552470s